Brook PS4+ Audio Fighting Board Thread

1235»

Comments

  • GOGO.ZippyGOGO.Zippy Joined: Posts: 1,106
    @GOGO.Zippy Nevermind, it was because I had the "2 analog sticks" jumper disconnected. Thanks.

    @VarmintBaby
    Yes, please look it
    brookaccessory.com/Archive/_eng/upload/p4+FightingBoardAudio_EN_05-2.jpg
  • madmalkavmadmalkav Joined: Posts: 60

    You need a TRRS jack with an internal pass-through on the ground signal (second ring).

    I confess I was absolutely unable to find the described part by myself. If someone could point me to a valid part I'll really appreciate it.
  • jopamojopamo Stuck in Silly-con Valley Joined: Posts: 1,370
    edited January 5
    It’ll be difficult to find a 4-conductor TRRS pass though mount jack with ground/earth as the center two rings. Many if not most have them as tip or sleeve. You could do a breakout board like the one below, but mount options are limited...

    https://www.sparkfun.com/products/11570

    Why don’t you want to use the provided USB/Audio breakout board??
  • chunk127chunk127 Joined: Posts: 2
    I need some help here. I set up a game room solutions arcade set with a zero delay encoder and used Happ buttons and microswitches to save money. I got two of these boards for Christmas so I can play games like Injustice and MKX on it.

    The problem is these boards are completely different so the wires don't fit. I got what I thought were the wires for it only to find they were way too small for the microswitches to connect to.

    What kind of wiring do I need since I doubt I can fit 30 ground wires in two ground slots.
  • jopamojopamo Stuck in Silly-con Valley Joined: Posts: 1,370
    edited January 6
    There are two versions (Japanese or American) of the Zero Delay Encoder board kits. Each version has different sized wired quick-disconnects (.110” for Japanese, .187” for American)to accommodate the appropriate sized contacts on your buttons.

    Chances are...you bought the kit for Japanese-style controls...which means it’s time to check that return policy :wink:

    P.S. Zero delay encoders have nothing to do with the subject of this particular thread. Please use the appropriate Q&A sticky thread for posts like that in the future. Thanks.
    Post edited by jopamo on
  • veohamveoham Joined: Posts: 1
    jopamo wrote: »
    Why don’t you want to use the provided USB/Audio breakout board??

    Not the original poster, but in my case I'm looking to use a GX aviation connector for USB and keep audio. I don't historically trust micro USB.
  • VarmintBabyVarmintBaby Joined: Posts: 638
    @veoham The revision 2 of the Brook PS4+ board doesn't use micro USB. Have you gotten the board already and have the older one? If not the new one should be fine with USB B.
    "Play the game to learn not to win. Do this and winning will start to come all on its own." - some smart guy
  • madmalkavmadmalkav Joined: Posts: 60
    jopamo wrote: »

    Why don’t you want to use the provided USB/Audio breakout board??

    Don't trust microUSB at all. I finally surrended and bought the board assuming probably I wouldn't find an alternative but wanted to try anyway. A week later the revision with USB-B announced but Brook won't sell the breakout board alone.
  • jopamojopamo Stuck in Silly-con Valley Joined: Posts: 1,370
    edited January 15
    Buy the newer kit and flip the old one on Trading Outlet (or eBay) to recoup at least some of the value. You’re going to be wasting a bunch of time by swimming upstream with the DIY route. Look...it’s this easy.
    BROOK-PS4SOUND-BREAKOUT-V2017-34__03269.1504031421.1280.1280.jpg
1235»
Sign In or Register to comment.