I think you are getting the wire in the wrong spot. It happens to me as well. If the little metal sheild isn’t fully “up” when the screws are loosened… the wires get above them and they come out.
Hmmm ok I’ll try disconnecting everything and unmounting the board and try again.
I just got mine today as well. I noticed that it came with the USB connector screws all the way to the top. You need to loosen it so that the catch would lower. Once the catch is lowered, you can then insert your wires into the catch. Then you tighten it back up. I hope that helps.
I got my EZmod w/ Brook UFB today for the TE2+ and have installed it but am running into an issue. The controller auto detects and works fine on the PS3 and PS4 but I can’t get it to work on the Wii U, Xbox 360, or Xbox One. When I plug it in, the player indicator LEDs would light up for a brief second, at the same time, the DP LED stays lit. However, it just does not work on those systems. I’ve upgraded the firmware to 1.8 as well. Note that I am using a Mac. Here are pictures of my install:
Note: that there’s a blinking green LED in addition to the solid green LED.
Note: UFB LED is constantly on.
Also not sure what these cables are for, should they be used at all? If so, where?
Those two extra cables connect between the tow unused connectors on the TE2+ EZ MOD and the Brook UFB. One is for future touchpad support (if they implement) and the other is the DP/RS/LS connector.
It sounds like the EZ MOD is working fine, but the Brook UFB is not. My board routes signals only and doesn’t touch the USB lines whatsoever. That blinking light on the EZ MOD is a “heartbeat” that shows the code is executing in the EZ MOD that handles all of the Player LEDs, etc. Things that need some sort of processing to work with the Brook basically. All inputs like start, home, select, DULR, and the P1-K4, are simply passed right to the Brook. So if its not autodetecting, its an issue I can’t fix.
Try using the USB output on the Brook UFB with a USB cable and see if the situation is the same.
I tried your suggestion and connected a USB cable straight to the Brook, but it does not make a difference. Still not detecting my XBox and Wii U.
Btw, the connector for the LS/DP/RS is too thick and doesn’t fit the Brook connector. I think I need a slimmer cable, like the one for the USB (J6-1).
That connector on the Brook isn’t the correct one for the EZ MOD; it’s not what I include at least with the kits. That’s probably why it doesn’t fit. Did you get the board in an EZ MOD kit or did you buy it from somewhere other than ArcadeShock?
Other than that, I suspect there is something else wrong with the UFB. If it has been updated to the current FW; I’m at a loss as to why it’s not working with 360/wii u/One. @GOGO.Zippy - thoughts?
Got it as a kit from ArcadeShock: https://arcadeshock.com/products/ez-mod-for-te2-plus-version-w-brook-ufb-soldered-headers-package. Where can I get a slimmer cable connector, like the one you include for the USB/J6-1 connection? Would Fry’s have something like that? I think that will fit the presoldered LS/DP/RS connector on the Brook.
Yeah. I updated to the latest firmware via my Mac. Basically:
- I downloaded the firmware (1.8),
- opened it,
- pressed PS and Share button while plugging in the controller (as instructed by firmware installation instructions)
- updated firmware
- clicked on “done”/“complete” button after the firmware updated
- unplugged the controller
Tried it across my systems and it only works on the playstations.
Typically yes, though you just need something from Harwin via digikey thats 1x4 .100" connectors.
One thing to try… the legs on the connector should face UP for the Stick Selector switch. Are the pins bent down a bit? It might just take a little manual manipulation to make it fit since Molex does make a “naked” version of the KK connector as well that mates with the cables included.
It seems like this link to the EZ mod for TE2+ with connectors (https://arcadeshock.com/products/ez-mod-for-te2-plus-version-mad-catz) has gone dead. Does this mean no restock soon?
Probably means they sold out of premade kits.
I just bought a TE2+ and the buttons are squashy and way too sensitive. And the joystick is not stiff at all, feels like it is all over the place. Not what I expected for paying 220$. I have two questions. The first is are the Sanwa 30mm you buy online any better?and if not what brand is better.
The second questions is if I’m going to spend another 60-80$ modding the TE2+, should I just buy the qwanba dragon? Is it just as good or better?
Sanwa buttons are sanwa buttons, no difference in any stick you get them in. The Dragon uses the exact same, just a different color. The lever is the same deal as well. Sanwa JLF in both cases. If you are going to want to make it stiffer, get a new heavier spring.
Also, this is off topic. This is the TE2/TE2+/TES+ EZ MOD thread which has nothing to do with the buttons and levers installed in these sticks.
Sorry, I’m new to this, just need to know how to get stiff responsive buttons.
Please use the search function of the forums. There are hundreds of discussions on personal preference on buttons and levers.
Just buy a button that is physically stiffer to push.
In general Seimitsu buttons are stiffer than Sanwa.
get seimitsu buttons.
or Sanwa RGs